How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have a unique set of steps to add an additional key. It requires dealer service using an electronic handheld computer called Tech-2. A new key and transponder have to be purchased and then programmed into the car.
Change your keys regularly to prevent one from wearing out quicker than the next. This will help to keep your keys in top condition.
Replacement Case
In contrast to the traditional Saab keys of the past keys, the new key fobs have electronics inside which makes it more difficult to create a duplicate. This has made car theft considerably more difficult than it was years ago. However, it also has made the replacement of lost keys a comparatively expensive task.
Every owner of a Saab 9-3 should have at minimum two working keys. It's expensive to replace a lost or damaged key since it requires replacing the CIM module, as well as programming the locking cylinders. Dealers will typically charge $100-$200 to do this.
There are ways to cut down on these costs. Some parts suppliers will look up the code from a spare key (usually the same one that opens the doors and turns on the ignition) and cut a new key blade out of metal for less than the dealer's cost. The key, however, must be the same as the original one to function properly in your vehicle.
You can also replace the case yourself by following these steps. You will need a flathead screwdriver and some patience. Using the screwdriver, slowly pry the plastic apart and remove the emergency key from the case. Once the case has been opened, remove all electronics and put them back in the new case. Make sure you put the correct key and badge back in the case too.
Replacement Battery
The Saab 9-3 replacement battery is an inexpensive component that can be quickly and easily replaced. This video tutorial on DIY from YouTube user Cyclone Cyd explains how to replace the battery of the remote key fob in just four steps. This guide should work with any modern saab-type key fob, although the process might differ slightly.
The button is normally located close to the Saab logo on the back of the fob. It's usually just below the Saab logo on the back of the fob. Next, use an screwdriver with a flat head to insert into the tiny hole in this button. This will allow you to open the fob's case to allow you to replace the battery.
Once the new CR1632 battery is in place You can then reassemble the remote key fob and then program it to your car. The procedure should take no more than a half hour at the most. It is a simple process that does not require any special tools.
If you lose your key, the procedure will be slightly more complicated, but it can still be accomplished. The dealer will have to verify the VIN of the car, and then request a replacement key blade and TWICE module that has the correct unique code. The dealer will then need to program the key using MDI, a new software tool.
Replacement Key Fob
The key fob is the part that locks and unlocks your car, it has a battery inside. The batteries last for a certain time and will eventually fail. It's a common issue that affects all cars. The good news is you can replace the battery on most key fobs, without having to replace the entire case. You can purchase fobs replacements on Amazon that include all the electronics already installed, so you'll be able to simply open the case and replace the batteries that were in the case. It is important to keep in mind that you'll have to remove the emergency key first, and you can accomplish this by inserting the screwdriver of a small flathead into the slot in the middle of the case. The case should split when you rotate the screwdriver around it.
If you're ready to change your keys, have a spare on hand. This will save you lots of money. If you do have a spare, you can have the dealer cut an additional key and program it to the car, which is cheaper than replacing the whole key fob.
If you do not have a spare key car key, you can add an additional key to your car, but this requires a lot research and effort. Adding a second key costs around a hundred dollars and it requires programming of the car's computer. This can be done by a professional, however it's a costly choice for the majority of owners.
Replacement Ignition
In contrast to earlier Saab cars, the modern SAAB 9-3 models have an advanced alarm system that is built around a coded key. This means that should you lose only one functioning key, getting another one could be very expensive because the car needs to have a special computer module installed and it also needs to be specifically programmed to accept an additional key. Most locksmiths can't do this and dealers can charge several hundred dollars just to program the new key!
Dealers will charge you a high price to replace your car computer (also known as the CIM or SAAB twice) If you lose your only functioning key. We can reprogram the EEPROM on your car's computer so that it is prepared for a new key. This will save you more than 50% of the cost you would spend at an auto dealer.
If you've been a long-time owner of a 03-11 SAAB 9-3, then you likely realize that the ignition key isn't really all that durable. If the ignition key you have isn't functioning properly, it is time to consider replacing it. replacement saab 9-3 key can become very sticky and the buttons can fall off. Luckily, replacing the ignition key isn't as complicated as it seems, and it can be done quickly using the appropriate tools.